Hi Guys,
Just want to bring to your attention I had an issue with my new PC last night where alll of a sudden the H110i Cooler started being glitchy. I first noticed there was an erratic fan behaviour up and down then I head the device connect/ disconnect system beep like a usb plug in sound. Then I went into the Corsair Link and noticed the Pump was showing RPM of 0 and the 2nd H110i Fan had disappeared from it. So to try and rectify I did the following:
1. Reboot - Issue not resolved.
2. Shutdown and restart - Issue not resolved.
3. Then I noticed the Corsair Link was showing there was an update available so clicked on that and did a reboot - Issue not resolved.
4. On the reboot it said update was available again so figured it might have been a corrupted update so uninstalled Corsair Link and rebooted - Issue not resolved.
All the time I had noticed there was no temp issues so everything seemed to be working, just buggy. So with all software related options exhausted I went with hardware so I did the following:
1. Changed Fan Headers - which I need to add that due to cable management it left very little room for manovering, but just enough with a bit of effort to re-route it next to the CPU fan header. Restarted - Issue not resolved.
2. Re-Installed the Corsair Link to see if any change to the display but the 2nd H110i Fan was still missing and the H110i Pump reading at 0 RPM.
2. Changed to the second USB 2.0 Header - again as above due to cable management it made and easy job difficult but there was just the bare minimum to reach it. Restarted - Issue not resolved.
3. Unplugged the the USB connecter from the cooler cpu block and reconnected, even though it was secured tightly. Restarted - Issue finally resolved - Corsair Link now seeing the 2nd H110i Fan and the the Pump RPMs now also reading correctly. No more connect/ disconnect issues.
So not sure if one of the fan headers/ usb headers have failed and it needed to be reconnected to register my change or if something glitchy was with the USB Connector and re-connecting it fixed the issue.
So best case scenario I have fixed the issue and will not need to comeback on the post. Worst case scenario it was only a plaster and the H110i Cooler is faulty with imminent total failure pending.
But said I better report it either way.
Regards
Mark
Just want to bring to your attention I had an issue with my new PC last night where alll of a sudden the H110i Cooler started being glitchy. I first noticed there was an erratic fan behaviour up and down then I head the device connect/ disconnect system beep like a usb plug in sound. Then I went into the Corsair Link and noticed the Pump was showing RPM of 0 and the 2nd H110i Fan had disappeared from it. So to try and rectify I did the following:
1. Reboot - Issue not resolved.
2. Shutdown and restart - Issue not resolved.
3. Then I noticed the Corsair Link was showing there was an update available so clicked on that and did a reboot - Issue not resolved.
4. On the reboot it said update was available again so figured it might have been a corrupted update so uninstalled Corsair Link and rebooted - Issue not resolved.
All the time I had noticed there was no temp issues so everything seemed to be working, just buggy. So with all software related options exhausted I went with hardware so I did the following:
1. Changed Fan Headers - which I need to add that due to cable management it left very little room for manovering, but just enough with a bit of effort to re-route it next to the CPU fan header. Restarted - Issue not resolved.
2. Re-Installed the Corsair Link to see if any change to the display but the 2nd H110i Fan was still missing and the H110i Pump reading at 0 RPM.
2. Changed to the second USB 2.0 Header - again as above due to cable management it made and easy job difficult but there was just the bare minimum to reach it. Restarted - Issue not resolved.
3. Unplugged the the USB connecter from the cooler cpu block and reconnected, even though it was secured tightly. Restarted - Issue finally resolved - Corsair Link now seeing the 2nd H110i Fan and the the Pump RPMs now also reading correctly. No more connect/ disconnect issues.
So not sure if one of the fan headers/ usb headers have failed and it needed to be reconnected to register my change or if something glitchy was with the USB Connector and re-connecting it fixed the issue.
So best case scenario I have fixed the issue and will not need to comeback on the post. Worst case scenario it was only a plaster and the H110i Cooler is faulty with imminent total failure pending.
But said I better report it either way.
Regards
Mark
